ifconfig為什么沒有顯示對應IP信息

這篇文章將為大家詳細講解有關ifconfig為什么沒有顯示對應IP信息，文章內容質量較高，因此小編分享給大家做個參考，希望大家閱讀完這篇文章后對相關知識有一定的了解。

服務器之前可以連通192.167.10.11的，現在突然ping不同了。
1、ifconfig和ip addr都看不到本機192.168.10網段的IP
2、cat /etc/sysconfig/network-scripts/ifcfg-em2發現有192.168.10網段的IP，以為網線被拔掉了，后來到機房看網線是插好的
3、繼續查詢才發現192.168.10網段的IP對應的ONBOOT=no，重新ifconfig em2 up后解決


[root@ebsdev ~]# history |grep mount
  704  mount 192.167.10.11:/volume1/dbsbak /dbsbak
  742  umount /dbsbak

--ifconfig沒有顯示192.168.10網段的IP
[root@ebsdev vbpbak]# ifconfig 
em2       Link encap:Ethernet  HWaddr A4:BA:DB:36:9B:38
          inet6 addr: fe80::a6ba:dbff:fe36:9b38/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:31624404 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:2783785598 (2.5 GiB)  TX bytes:270 (270.0 b)

128       Link encap:Ethernet  HWaddr A4:BA:DB:36:9B:37
          inet addr:192.168.128.172  Bcast:192.168.128.255  Mask:255.255.255.0
          inet6 addr: fe80::a6ba:dbff:fe36:9b37/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:139452228 errors:0 dropped:0 overruns:0 frame:0
          TX packets:31576165 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:38000646597 (35.3 GiB)  TX bytes:24891534426 (23.1 GiB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:731881261 errors:0 dropped:0 overruns:0 frame:0
          TX packets:731881261 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:116710422261 (108.6 GiB)  TX bytes:116710422261 (108.6 GiB)

--ip addr沒有顯示192.168.10網段的IP
[root@ebsdev vbpbak]# ip addr  
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: 128: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
    link/ether a4:ba:db:36:9b:37 brd ff:ff:ff:ff:ff:ff
    inet 192.168.128.172/24 brd 192.168.128.255 scope global 128
    inet6 fe80::a6ba:dbff:fe36:9b37/64 scope link
       valid_lft forever preferred_lft forever
3: em2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
    link/ether a4:ba:db:36:9b:38 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::a6ba:dbff:fe36:9b38/64 scope link
       valid_lft forever preferred_lft forever


[root@ebsdev vbpbak]#  cat /etc/sysconfig/network-scripts/ifcfg-128
HWADDR=A4:BA:DB:36:9B:37
TYPE=Ethernet
BOOTPROTO=none
IPADDR=192.168.128.172
PREFIX=24
GATEWAY=192.168.128.1
DEFROUTE=yes
IPV4_FAILURE_FATAL=yes
IPV6INIT=no
NAME=128
UUID=4c153aa8-ab08-48d0-995a-87a8e0c681a9
ONBOOT=yes
DEVICE=128
USERCTL=no
NETMASK=255.255.255.0

有192.168.10網段的IP
[root@ebsdev vbpbak]# cat /etc/sysconfig/network-scripts/ifcfg-em2
DEVICE=em2
HWADDR=a4:ba:db:36:9b:38
TYPE=Ethernet
UUID=5de6d96b-6691-4a3d-ac3c-1eda48ca9db8
ONBOOT=no
NM_CONTROLLED=yes
BOOTPROTO=none
IPADDR=192.167.10.25
NETMASK=255.255.255.0
IPV6INIT=no
USERCTL=no


解決方法
ifconfig em2 up

關于ifconfig為什么沒有顯示對應IP信息就分享到這里了，希望以上內容可以對大家有一定的幫助，可以學到更多知識。如果覺得文章不錯，可以把它分享出去讓更多的人看到。