OSPF高級配置實驗

OSPF高級配置實驗

一.實驗環境

實驗環境：gns3，c2691路由器

二.實驗拓撲圖<img src="https://cache.yisu.com/upload/information/20200309/33/53147.jpg" alt="mark" style="zoom:75%;" />

三.實驗步驟

因為路由器比較多，我們一個個來。R1配置<img src="https://cache.yisu.com/upload/information/20200309/33/53148.jpg" alt="mark" style="zoom:75%;" />

接下來配置R2<img src="https://cache.yisu.com/upload/information/20200309/33/53149.jpg" alt="mark" style="zoom:75%;" />

由于R2下面還有兩個網段。所以我們還得做一個靜態路由。<img src="https://cache.yisu.com/upload/information/20200309/33/53150.jpg" alt="mark" style="zoom:75%;" />

我們還得將R2下面的兩個網段宣告一下，一個直連一個非直連。<img src="https://cache.yisu.com/upload/information/20200309/33/53151.jpg" alt="mark" style="zoom:75%;" />

接下來配置R3ip地址<img src="https://cache.yisu.com/upload/information/20200309/33/53152.jpg" alt="mark" style="zoom:75%;" />

<img src="https://cache.yisu.com/upload/information/20200309/33/53153.jpg" alt="mark" style="zoom:75%;" />

然后我們先把默認路由配置好<img src="https://cache.yisu.com/upload/information/20200309/33/53154.jpg" alt="mark" style="zoom:75%;" />

然后我們把網段分配area<img src="https://cache.yisu.com/upload/information/20200309/33/53155.jpg" alt="mark" style="zoom:75%;" />

注意這里還有一個70段的網段，為了方便我們將其放入area 0<img src="https://cache.yisu.com/upload/information/20200309/33/53156.jpg" alt="mark" style="zoom:75%;" />

我們還得將外部的默認路由宣告進來<img src="https://cache.yisu.com/upload/information/20200309/33/53157.jpg" alt="mark" style="zoom:75%;" />

接下來我們配置R4的ip<img src="https://cache.yisu.com/upload/information/20200309/33/53158.jpg" alt="mark" style="zoom:75%;" />

然后將rip協議配置好<img src="https://cache.yisu.com/upload/information/20200309/33/53159.jpg" alt="mark" style="zoom:75%;" />

然后將ospf協議注入rip<img src="https://cache.yisu.com/upload/information/20200309/33/53160.jpg" alt="mark" style="zoom:75%;" />

然后還得再將40網段分配下給area0<img src="https://cache.yisu.com/upload/information/20200309/33/53161.jpg" alt="mark" style="zoom:75%;" />

然后還得再次將rip協議注入ospf協議<img src="https://cache.yisu.com/upload/information/20200309/33/53162.jpg" alt="mark" style="zoom:75%;" />

接著對R5配置接口ip<img src="https://cache.yisu.com/upload/information/20200309/33/53163.jpg" alt="mark" style="zoom:75%;" />

然后配置好rip協議

<img src="https://cache.yisu.com/upload/information/20200309/33/53164.jpg" alt="mark" style="zoom:75%;" />

然后配置R6接口ip地址<img src="https://cache.yisu.com/upload/information/20200309/33/53165.jpg" alt="mark" style="zoom:75%;" />

然后配置下靜態路由

<img src="https://cache.yisu.com/upload/information/20200309/33/53166.jpg" alt="mark" style="zoom:75%;" />

至此，完成實驗。可以去ping下pc。沒問題應該是全網互通。